 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
|
|
|
|
||
Baumer |
||
|
Baumer Electric is an organisation that is now an international
leader in the field of precision sensors and has its origins in the
pioneering work that was carried out by Herbert Baumer, a qualified
electrical engineer. Distance sensors The compact laser distance sensors provide a precise output signal which is proportional to the measured distance. The optical principle is based on triangulation. Through beam sensors Emitter and receiver are in two separate housings facing each other. Through beam sensors offer the largest sensing ranges. Sensitivity adjustment (photoelectric sensors) The sensing distance (Sn) of the capacitive sensor may be adjusted by means of a inbuilt potentiometer. Copy counter (SCATEC) Laser copy counters are primarily developed for non-contact counting of printed matter in a lap stream. Basically a SCATEC responds to an edge passing through the laser beam with an output pulse. Capacitive sensors Position sensor for detecting conductive and non-conductive materials 3D-CAD models For most of our products of this section we provide 3D-CAD models for Download. Just browse to the appropriate sensor product or enter the product code (order reference) in full, or enter parts into the search field. High temperature sensor High temperature sensors usually consist of two parts: a high temperature probe and an inline electronic amplifier. Both are linked with a Teflon cable. Advantages: reliable detection up to 200°C. Sensing distance Sn adjustable The sensing distance of the capacitive sensor may be adjusted by means of a inbuilt potentiometer. Ultrasonic sensors Blind range St Reliable object recognition is not possible within the blind range (St). Objects within this blind range may cause false switching of the sensor. Scanning range far limit Sde The scanning range far limit Sde can be continuously adjusted either by the built-in pot or by teaching in. Scanning range close limit Sdc The scanning range close limit Sdc can be electronically set using the sensor's Teach-in features. Hysteresis Hysteresis is the difference between the sensing point of the approach and the removal of a target. Smart Vision Sensors Actuator Sensor Interface The AS-Interface system solution offers a viable alternative to the present parallel cable harness. It is the only bus system that can transfer data and energy via a simple two-wire line. The sensors and actuators are connected by means of a simple, insulation-free connection method. Encoders and Motion Control Absolute MT encoders detect the rotation of a drive axis over several revolutions. In absolute ST encoders, each angular position is well assigned to a definite position value. This absolute position value is available immediately after system switch-on. Therefore, a reference run is not necessary. Incremental encoders are dedicated for precise measurement of angle, speed or direction of rotational movements. Actuator and positioning drives Positioning drive MSIA Dynamically and precisely For optimum performance, lifetime and control properties, the positioning drive MSIA has an integrated brushless DC motor. Actuator MSAA Compact and decentralized The actuator MSAA is equipped with an absolute position encoder. Therefore, time-consuming reference runs are not necessary. Actuator MDBA Simple and cost-effective. For simple and cost-effective format change with an already existing external control which works without fieldbus. Magnetic sensors Magnetic sensor for rotary applications The MDFK type of magnetic encoder consists of a magnet rotor and a magneto resistive sensor. May be used just like a standard incremental encoder. Advantages: easy installation, low cost alternative to standard encoders, up/down recognition possible Magnetic sensors Magnetic sensors optimized for rotary and linear applications. Non contact potentiometer MDRM & MDFM magnet sensors can be used as non-contact potentiometers. They are magnetically controlled by a rotor positioned in front of the active face. Advantage: for applications in harsh environments, no moving parts, sine / cosine output signals, linear 1...9 VDC/4...20 mA absolute values Precision limit switches My-Com Activating force Depending on the My-Com type an activating force in the range of 30 cN to 100 cN is required to open the switch. Special versions may require up to 250 cN. Silicone My-Coms featuring an IP 67 protection class are usually sealed with a bellow type silicone gasket. Actuator tip The actuator tip of a standard My-Com is made of zirconium oxyde ZrO2. Hard metal or ruby is used for a selected number of special types. Overrun Depending on the My-Com type the overrun is between 0,6 and 1,5 mm Transmitters Transmitters are pressure sensors with integral electronic amplification. They are available with a variety of three-conductor voltage outputs and a two-conductor current output. Baumer transmitters are particularly suitable for demanding industrial applications in ambient temperatures up to +85 °C. |
||
| Baumer, and more other brands, our quality at your service; for more informations about Baumer products visit our site. | ||
Balluff |
Baumer |
Berges |
Danaher |
Dynisco |
Elettronica Santerno |
Esa |
Gefran |
Givi Misure |
Hohner |
Lenze |
Md Micro Detectors |
Meanwell |
Moeller |
Sew Eurodrive |
Siei |
Techno Gr |
Tecnologic |
Turck Banner |
Vacon |
Wenglor |
Wika
|
||
